On this page
In Units and Measurement, most assertion-reason statements look like simple rules. Marks go to whoever checks each rule exactly and asks whether the reason really causes the assertion.
What do these Units and Measurement questions cover?
Every item stays inside Unit 1, Physics and Measurement, of the NEET (UG)-2026 syllabus published by the National Medical Commission. Statements were checked against NCERT Class 11 Physics, Chapter 1, Units and Measurement (Reprint 2026-27); least count and error items use standard rules, and every number was checked with Python. New to the chapter? Read our guide on how to prepare Physics and Measurement for NEET.
How do you answer assertion-reason questions?
Judge each statement alone. If both are true, say "A, because R" and check that it holds.
Assertion-reason keys (Q1 to Q6):
(A) Both A and R are true and R is the correct explanation of A.
(B) Both A and R are true but R is NOT the correct explanation of A.
(C) A is true but R is false.
(D) A is false but R is true.
Statement I and II keys (Q7 to Q10):
(A) Both statements are correct.
(B) Both statements are incorrect.
(C) Statement I is correct, Statement II is incorrect.
(D) Statement I is incorrect, Statement II is correct.
Assertion-reason questions on Units and Measurement
Q1 (easy). Assertion (A): Plane angle and solid angle are dimensionless quantities. Reason (R): Each is defined as a ratio of two quantities with the same dimensions: arc length to radius, and area to the square of the radius.
Answer: (A). Both are true. A ratio of similar quantities has no dimensions, so R is the direct cause of A.
Trap: thinking a named unit, like rad, implies dimensions.
Q2 (easy). Assertion (A): A length recorded as 0.05080 m has four significant figures. Reason (R): In a number less than 1, the zeros to the left of the first non-zero digit are significant.
Answer: (C). A is true: 5, 0, 8 and the trailing 0 make four. R is false: leading zeros only place the decimal point.
Trap: counting every zero you can see.
Q3 (medium). Assertion (A): Dimensional analysis alone can prove that the centripetal force on a body is exactly mv²/r, with no extra numerical factor. Reason (R): Multiplying one side of an equation by a pure number does not change its dimensions.
Answer: (D). A is false: dimensions give F = k·mv²/r, and k stays unknown. R is true, and it is why k cannot be found.
Trap: treating a dimensionally consistent result as complete.
Q4 (medium). Assertion (A): Writing 6.040 cm as 0.06040 m does not change the number of significant figures. Reason (R): In multiplication or division, the result keeps as many significant figures as the factor with the fewest.
Answer: (B). Both are true. A holds because changing units cannot change precision. R is a rule for arithmetic, not unit conversion.
Trap: picking (A) because both mention significant figures.
Q5 (medium). Assertion (A): If the radius of a wire is measured with a 1% error, the area of its cross-section, πr², carries a 2% error. Reason (R): When a measured quantity is raised to the power k, its relative error is multiplied by k.
Answer: (A). Both are true. Area goes as r², so the error doubles to 2%; π is exact. R is the rule that produces A.
Trap: adding an error for π, or forgetting to double.
Q6 (hard). Assertion (A): If the units of length and time are both doubled, the numerical value of a given acceleration is halved. Reason (R): For a given physical quantity, the numerical value times the unit is the same in every system of units.
Answer: (D). A is false. For [L T⁻²] the new number is n × (1/2) × (1/2)⁻² = 2n, so 8 m s⁻² becomes 16. R is true, and applying it disproves A.
Trap: dividing by 2 for length and ignoring the square on time.
Statement I and Statement II questions on Units and Measurement
Q7 (easy). Statement I: The SI has seven base units, and the candela and the mole are two of them. Statement II: The radian is one of the SI base units.
Answer: (C). I is correct. II is incorrect: the radian is a dimensionless ratio of lengths, not a base unit.
Trap: assuming every unit in an SI table is a base unit.
Q8 (medium). Statement I: Rounded to three significant figures by the NCERT convention, 3.465 becomes 3.46. Statement II: By the same convention, 7.835 becomes 7.84.
Answer: (A). Both are correct. When the dropped digit is 5, the preceding digit stays if even (6) and rises by 1 if odd (3).
Trap: always rounding 5 upwards.
Q9 (medium). Statement I: The product 3.0 cm × 2.45 cm should be reported as 7.35 cm². Statement II: The sum 25.36 g + 4.1 g + 0.248 g should be reported as 29.7 g.
Answer: (D). I is incorrect: 3.0 has two significant figures, so 7.4 cm². II is correct: a sum keeps the fewest decimal places, so 29.708 g becomes 29.7 g.
Trap: swapping the product rule and the sum rule.
Q10 (hard). Statement I: A vernier calliper whose 10 vernier divisions equal 9 main-scale divisions of 1 mm has a least count of 0.01 mm. Statement II: If the mass of a cube is measured with a 2% error and its side with a 1% error, the maximum error in its density is 3%.
Answer: (B). Both are incorrect. Least count = 1 MSD − 1 VSD = 1 mm − 0.9 mm = 0.1 mm. Density = m/L³, so the maximum error is 2% + 3 × 1% = 5%.
Trap: mixing up vernier and screw gauge, or forgetting the cube.
How should you use this set?
Sort every miss: wrong about A, wrong about R, or wrong about the link.
For each link miss, write the real reason in one line.
For each truth miss, reread that NCERT section.
If Q6 or Q10 went wrong at a step you cannot spot, the Fermi Problem Library has worked problems with a step-by-step solver that explains the reasoning rather than printing an answer.
For timed MCQs on this chapter, try our Physics and Measurement NEET practice questions with solutions. For a method for any subject, see our three-check strategy for assertion-reason questions.



